• Shopping Cart
  • Contact Us
  • Select a Location
    Close Location Selection

    Current Location:

    Let us know the location you'd like to browse.

    Select a Location
    OR
  • View Cart

Netgear CM1100

Details

     

Modem Information

DOCSIS 3.1 Cable Modem

32x8 channel bonding

Compatible with future speed increases.

Highest Service Level

Gigablast

   

Front View

Image of Front of the Netgear CM1100

Click to enlarge.

After the cable modem successfully registers on the network, the Power, Upstream, Downstream, and Internet indicators illuminate continuously to indicate that the modem is online and fully operational. For more details, refer to the Modem Lights section.

     

Back View

Image of back of the Netgear CM1000

Click to enlarge.

 

The Netgear CM1100 has the following ports available on the back of the modem.

  • Reset Button - Use this button in the unlikely event that you want to restore the default factory settings. This button is recessed to prevent accidental resets of your modem.
  • LAN Gigabit Ethernet Ports - Use these ports to hardwire connect this device to the internet.
  • Cable / Internet Coaxial Cable Connector - Connect your coaxial cable line to this port.
  • Power On / Off Button
  • Power Adapter Input - Connect the supplied power cord to this port.
     

MAC Address

Image of Netgear CM1100 MAC Label

Click to enlarge.

 

MAC addresses are written as 12 digits containing both letters and numbers (0-9, A-F). A MAC address is unique. The first six characters of the MAC address are unique to the manufacturer of the device.

Modem Lights

The modem lights indicate the current status of your cable modem. To troubleshoot any connection problems, use the table below.

Modem Light Status Problem
Power

power
Off No power. Verify all cable connections and try resetting the modem. If cable is OK and modem reset does not work, contact Customer Support.
Green None - Power is supplied to the cable modem.
Red

The cable modem is too warm and might overheat:

  • Disconnect the power adapter.
  • Wait a couple of minutes to let the cable modem cool down.
  • Make sure that the cable modem is placed in a vertical position.
  • Make sure that the cable modem is placed in a location with good ventilation.
  • Reconnect the power adapter.
Downstream

downstream
Solid Amber None. Connection established on one channel.  
Blinking Green Scanning for additional downstream channels.  
Solid Green None. Operating on more than one channel.  
Off Downstream channel inactive. Verify all cable connections and try resetting the modem. If cable is OK and modem reset does not work, contact Customer Support.  
Upstream

upstream
Off Upstream channel inactive. Verify all cable connections and try resetting the modem. If cable is OK and modem reset does not work, contact Customer Support.  
Blinking Green Scanning for additional upstream channels.  
Solid Amber None. Connection established on one channel.  
Solid Green None. Operating on more than one channel.  
Internet

internet
Off Modem offline. Verify all cable connections and try resetting the modem. If cable is OK and modem reset does not work, contact Customer Support.  
Blinking Green None. Scanning for configuration parameters. Verify all cable connections and try resetting the modem. If cable is OK and modem reset does not work, contact Customer Support.  
Solid Green None. Operational.  
Ethernet

ethernet
Off A device is not connected to the Ethernet port on the back. Connect a device to the Ethernet port on the back.  
Blinking Green or Amber None. An Ethernet port is transmitting or receiving data.  
Solid Amber None. A device is connected to the Ethernet port at 10/100 Mbps.  
Solid Green None. A device is connected to the Ethernet port at 1,000 Mbps.  

Manufacturer Resources

Search for More Articles

Image of 2 Chat Bubbles

Need More Help? Let's chat!

Chat live with a Cox agent to get the fastest answers to all your top questions.

Modal Id: ttps:--www.cox.com-residential-modals-support-call-jcr:content-parcontent-sectioncontainer.html